Leveling pad | SM 1270-2 A
from €10.07*
€10.07*
Delivery time: 1-3 days working days
Delivery time: 1-3 days working days
This product is available in 21 versions.
Product information "Leveling pad | SM 1270-2 A"
Jointed plate
Material:
Form A: ball bearing: heat-treated blackened
pad: steel
Form DN: ball bearing: stainless steel
pad: Thermoplast (POM)
Form NI: ball bearing: stainless steel
pad: stainless steel
Use as feet and pressure pieces.
They can be connected with most types of screws.
Non-parallel contact surfaces up to max. 15° degrees can be levelled out.
Temperature application range thermoplastic version from - 30 °C to + 80 °C.
RoHS-compliant: yes
| Compliance: | RoHS compliant |
|---|---|
| Element type: | Articulated foot, Feet / Wheels, Joint pieces, Joint plate |
| Material: | Bushing/Screw: Stainless Steel, Bushing/Screw: Steel, Plate: plastic POM, Plate: stainless steel, Plate: steel |
| Surface: | Steel - burnished |
Similar Items
Thrust pad - DIN 6311 | SM 1270
From
€1.81*
incl. VAT
with snap ring
Material: ST: steel case hardened, blackenedNI: stainless steelSpring retainer inlayed.Use with tommy screws DIN 6304 / SM 1235 and DIN 6306 / SM 1236,
with screws with pressure pins DIN 6332 / SM 1240 also as feet.The swivelling connection of the thrust pin and thrust piece enables adaptation to uneven clamping surfaces or clamping surfaces that are not perpendicular to the screw axis and prevents the rotary movement of the screw from being transferred to the clamping surface during clamping.
Mountage: The thrust piece is to be held in such a way that the snap ring lies in the recess and points with the open side downwards. The bolt is tilted towards the open side of the snap ring as far as possible and pressed in.
RoHS-compliant: yes
Thrust pad, flat - DIN 6311 | SM 1270-1
From
€3.86*
incl. VAT
with snap ringMaterial: ST: steel case hardened, blackened
NI: stainless steelSpring retainer inlayed.Low model with increased thrust area.Use with tommy screws DIN 6304 / SM 1235 and DIN 6306 / SM 1236,
with screws with pressure pins DIN 6332 / SM 1240 also as feet. The swivelling connection of the thrust pin and thrust piece enables adaptation to uneven clamping surfaces or clamping surfaces that are not perpendicular to the screw axis and prevents the rotary movement of the screw from being transferred to the clamping surface during clamping.Mountage: The thrust piece is to be held in such a way that the snap ring lies in the recess and points with the open side downwards.The bolt is tilted towards the open side of the snap ring as far as possible and pressed in.RoHS-compliant: yes
Leveling pad, anti-slip | SM 1270-2 AC
From
€11.54*
incl. VAT
with ball element and rubber capMaterial:Form AC: ball bearing: heat-treated steel, tempered, blackenedpad: heat-treated steel, tempered, blackenedForm CDN:ball bearing: stainless steel 1.4305pad: Thermoplast (POM), white
Form CNI: ball bearing: stainless steel 1.4305pad: stainless steel 1.4305Form C: with rubber cap for anti slipRoHS-compliant: yesUse as adjustable foot and thrust piece.Non-parallel bearing surfaces up to max. 15° degrees can be compensated.The plastic cap on the joint plate prevents slipping.The static load capacity is limited by the permissible load capacity of the joint ball.The values in the tables assume are based on a pure compressive load perpendicular to the joint foot.Bending/ buckling loads lead to a reduction in the load capacity and must be taken into account accordingly.
Leveling pad with bolt, anti-slip | SM 1270-2 BC
From
€19.54*
incl. VAT
with bolt, ball element and rubber capas anti-slip deviceMaterial:Form BC: ball bearing with bolt: heat-treated steel, tempered, blackenedpad: heat-treated steel, tempered, blackenedForm BCDN: ball bearing with bolt: stainless steel 1.4305pad: Thermoplast (POM), whiteForm BCNI: ball bearing with bolt: stainless steel 1.4305pad: stainless steel 1.4305Form C: with rubber cap for anti slipRoHS-compliant: yesUse as adjustable foot and thrust pieceNon-parallel bearing surfaces up to max. 15° degrees can be compensated.The plastic cover on the mounting pad prevents slipping.The static load capacity is limited by the permissible load capacity of the joint ball. The values in the tables assume are based on a pure compressive load perpendicular to the joint foot. Bending/ buckling loads lead to a reduction in the load capacity and must be taken into account accordingly.
Thrust pad | SM 1270-11
From
€2.64*
incl. VAT
with or without plastic capMaterial:ST: steel case hardened, blackenedNI: stainless steelRetaining spring: Stainless steel 1.4310Plastic cap:natural color, (Polyacetal POM),temperature resistant up to100 °CForm A: without plastic capForm K: with plastic capThe thrust pieces adapt to uneven or cylindrical surfaces and prevent transmission of the rotary movement of the screw to the workpiece.
The plastic caps prevent damage to delicate workpieces.Due to the special shape of the retaining spring, the thrust piece can be easily attached to the thrust pin and removed again without any problems.Use with tommy screws DIN 6304 / SM 1235 and DIN 6306 / SM 1236,with screws with pressure pins DIN 6332 / SM 1240 also as feet.RoHS-compliant: yes
Levelling foot | SM 3050
From
€6.50*
incl. VAT
with steel spindle and plastic baseMaterial:foot: plastic Technopolymer (Polyamide PA)glass fibre reinforcedtemperature resistant up to 100° black, matt threaded stud: steel, grade 5.8zinc plated, blue passivatedhexagon nut: steelzinc plated, blue passivatedrubber underlay: NBR 70 Shore hardnessblackForm A: without nut, without rubber underlayForm B: with nut, without rubber underlayForm C: without nut, with rubber underlay
Form D: with nut, with rubber underlayhigh static load capacity due to high-quality plasticand slightly stepped shape.Load distribution through ribbing over a large area.Articulated feet are supplied assembled, but can be dismantled.
Data on static load capacity are approximate values under exclusion of any liability for possible consequential damage when using the swivel feet.If the values are exceeded, permanent deformation or breakage of the plastic plate is possible.The values were determined by means of a series of tests in which a limited number of articulated feet were loaded for a limited time with a static force acting perpendicular to the plate.The suitability of the leveling feet for the respective application must be determined by the user.RoHS-compliant: yes
Levelling foot, stainless steel | SM 3051
From
€10.38*
incl. VAT
with stainless steel spindle and plastic baseMaterial: foot: plastic Technopolymer (Polyamide PA)glass fibre reinforcedtemperature resistant up to 100° Cblack, mattthreaded stud: stainless steel, 1.4305hexagon nut: stainless steel , 1.4301rubber underlay: NBR 70 Shore hardnessblackForm A: without nut, without rubber underlayForm B: with nut, without rubber underlayForm C: without nut, with rubber underlayForm D: with nut, with rubber underlayhigh static load capacity due to high-quality plasticand slightly stepped shape,Load distribution through ribbing over a large area.Articulated feet are supplied assembled, but can be dismantled.Data on static load capacity are approximate values under exclusion of any liabilityfor possible consequential damage when using the swivel feet.If the values are exceeded, permanent deformation or breakage of the plastic plate is possible.The values were determined by means of a series of tests in which a limited number of articulated feetwere loaded for a limited time with a static force acting perpendicular to the plate.The suitability of the leveling feet for the respective application must be determined by the user.RoHS-compliant: yes
Levelling foot, thread stud | SM 3061
From
€6.91*
incl. VAT
with stainless steel spindle and plastic base
Material:foot: plastic Technopolymer (PA)glass fibre reinforcedblack, matttemperature resistant up to 100° Cthreaded stud: stainless steel AISI 303hexagon nut: steel ISO 4032, stainless steel AISI 304rubber pad: (NBR) 70 Shore, black
Form B: with nut, without rubber padForm D: with nut, with rubber pad
Levelling feet are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a larger area.Levelling feet are supplied assembled, but are removable.
Information:If the values of the static load capacity given in the table are exceeded, the plastic foot plate may break. The values were determined by a series of tests in which a limited number of articulated feet were subjected to a static force acting perpendicular to the foot plate for a limited time.Depending on the application and load case, however, a safety factor must be taken into account so that the permissible load capacity is lower than the value given in the table.
RoHS-compliant: yes
Levelling foot, stainless steel | SM 3105
From
€6.18*
incl. VAT
Levelling foot, stainless steel
Material: foot: stainless steel No. 1.4301matt shot-blastedscrew: stainless steel, 1.4305hexagon nut: ISO 4032, 1.4305assembly screw.: stainless steeloctitedplastic cap: Elastomer (TPE) 80 Shorerubber underlay: (NBR) 70±5 Shore, black vulcanized
Form OS: without rubber cap, with nutForm KR: with rubber underlay clipped on, with nutForm GV: with rubber underlay vulkanized, with nut
The levelling feet can be used in some combinations of base plates and adjustable spindle versions.Screw versions M08/M10/M12 with external hexagon SW1. Screw versions M16/M20/M24 with hexagon socket at the top and wrench flat SW2 at the bottom. The base plate with the rubber underlay protects sensitive surfaces and reduces lateral slippage. The levelling feet are supplied fully assembled and are not removable.
RoHS-compliant: yes
Levelling foot - HYGIENIC DESIGN | SM 3150
From
€111.54*
incl. VAT
made of stainless steelwith adjustment sleeve
Material:foot plate: stainless steel 1.4301 (AISI 304), turnedspindle: stainless steel 1.4301 (AISI 304), turnedadjustable sleeve: stainless steel 1.4301 (AISI 304), turnedseals: blue, FDA compliant
Hardness:- sealing ring: NBR, hardness 70 ±5 Shore A- wiper: TPU, hardness 95 ±5 Shore A- joint sealing ring: H-NBR, hardness 85 ±5 Shore A- bottom seal: Silikon, hardness 85 ±5 Shore A
Form A: without boreForm B: with bore
These adjustable feet are certified according to the guidelines of 3-A Sanitary Standards,
Inc. and DGUV Testand the adjustable feet Form B with fixing holes are also certified
according to EHEDG and are therefore particularly suitable for use in hygienic areas.The bottom seal protects the area beneath the foot plate from dirt. For this, the foot
must be screwed on using the mounting holes and compressed accordingly. The
sealing ring above the adjustment sleeve enables fastening without dead space.Hygienic fasteners, such as screws and nuts SM 1265-9 and 1265-10, as well as It
is imperative that the mounting holes are inserted in the correct position. Due to the
wiper or the ball seal, the moving components are sealed against the environment.The high quality finish prevents adherence of dirt and facilitates cleaning.The values listed in the table for static load capacity refer to a purely vertical load
in relation to the leveling foot. Under normal operating conditions bending loads or
angular loads are not uncommon and result in a reduction of load capacity.
RoHS-compliant: yes
